Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterMighty Mule Gate Repair in Hollywood, FL | Vance Gate Repair Hollywood
Mighty Mule gate repair in Hollywood typically runs $185 to $460 depending on whether the control board, arm actuator, or receiver has failed. We’re Mighty Mule specialists and an independent service provider, not a manufacturer affiliate, and we carry the parts that fail most often on salt-exposed Hollywood properties. That’s the difference: we don’t guess, we stock. If your Mighty Mule opener stopped responding, the arm grinds, or the remote quit after a storm, call (754) 714-5786 and we’ll put the diagnosis in writing before any work starts.
Why Hollywood Residents Choose Us for Mighty Mule Service
We’ve worked on Mighty Mule openers in Hollywood long enough to know which failure modes repeat on this coastline and which are rare. The FM200, MM260, MM360, MM571W, and the newer MMKits all share a common weakness here: the control board’s connector pins corrode faster in the salt-spray corridor along the Intracoastal than they do 15 miles west. That means we test the board before condemning the motor, because replacing a $340 actuator when a $12 connector cleaning fixes the gate is something we refuse to do. Adrian Vance built this company after years of commercial access-control work, and the habit stuck: write down what we found, photograph what we changed, and hand you the record before we leave. We also service the other eight major gate brands, so if your Mighty Mule turns out to be a mismatch for a Hollywood Hills wrought-iron gate, we’ll tell you straight instead of steering you into a full replacement.
Common Mighty Mule Gate Repair Problems We Solve in Hollywood
- Control board failure from salt-air corrosion. On waterfront properties between Sheridan Street and the Hallandale Beach border, the board’s exposed solder joints and connector pins develop green corrosion within three to four years. Symptoms are intermittent operation, the gate stopping mid-cycle, or no response from the keypad. We replace with OEM Mighty Mule boards and apply a moisture barrier rated for coastal exposure.
- Actuator arm wear on original 1950s-to-1970s gates. Many Hollywood Hills and Liberia homes have original ornamental wrought-iron driveway gates that are far heavier than the Mighty Mule actuator was rated for. The arm’s internal gear strips, and the gate sags or stops halfway. We re-shim the gate, replace the gear assembly, and set the travel limits to account for decades of hinge wear.
- Remote and receiver failure after storms. The MM571W and MMKits receivers sit in a plastic housing that seals poorly against driven rain. After a hurricane-season storm, we regularly find water inside the receiver, a shorted antenna connection, or a fried logic chip. The fix is usually a new receiver board and re-pairing all remotes, not a new opener.
- Battery backup draining within hours. Mighty Mule’s battery kits are popular in western Hollywood’s HOA communities near I-75, where gates cycle 40 to 60 times a day during seasonal months. The battery’s charge controller fails, and the opener runs on AC while the battery stays dead. We test the controller, replace the SLA battery, and document the charging voltage.
- Photo-eye misalignment on sliding gates. The Mighty Mule photo-eye (the infrared beam that stops the gate if anything crosses the path) drifts out of alignment on sliding gates that sit on concrete pads cracked by Hollywood’s wet-dry cycles. The gate reverses for no apparent reason or refuses to close. We realign the beam, tighten the housing, and verify the obstruction reversal test passes before we leave.
Before
AfterMighty Mule Service in Hollywood: What Local Conditions Mean for Your Equipment
Hollywood sits inside Broward County’s High Velocity Hurricane Zone, and that changes everything about Mighty Mule repair here. Any new Hollywood Gate Installation or major component replacement must use Florida Product Approved parts rated for HVHZ wind loads, which means a simple actuator swap occasionally becomes a code compliance conversation about the entire gate system. We see this most often on older beachside homes near Young Circle, where a 1960s-era gate was never rated for current wind standards, and the moment we touch the operator, the permit inspector wants the gate’s wind-load certification too. On top of that, the dual salt-air exposure from the Atlantic shoreline and the Intracoastal Waterway cuts Mighty Mule operator lifespan from the 10-to-15-year norm down to 5 to 7 years on waterfront properties. Standard carbon-steel hinge pins and track bolts rust visibly within months here, so we keep 316 stainless fastener kits and marine-grade connectors on the truck as standard stock. That’s a Hollywood-specific inventory decision that changes how fast we can finish a repair.
Mighty Mule Models & Products We Service in Hollywood
We service the full Mighty Mule line: FM200, FM350, FM500, MM260, MM360, MM371, MM571, MM572, and the MMKits series (MMKits include the MM136, MM260, MM360, and MM571 kits, depending on your gate’s weight and swing). For parts, we use OEM Mighty Mule components whenever possible, because the aftermarket boards and actuators we’ve tested simply don’t survive Hollywood’s humidity profile. We stock OEM control boards, actuator arms, photo-eyes, receivers, and keypads in the van, which means we can often complete a same-day diagnosis and repair without waiting for a parts shipment. If your gate is a heavy wrought-iron original from the 1960s, we’ll tell you before we quote whether a Mighty Mule opener is even the right long-term solution for that weight class.
Mighty Mule Service Pricing in Hollywood
Most Mighty Mule repairs in Hollywood fall between $185 and $460, depending on what failed. A photo-eye realignment or limit switch adjustment is typically under $200. A receiver board replacement runs $210 to $320. A full actuator arm replacement, including the arm, mounting bracket, and limit re-set, runs $340 to $460. Control board replacement with an OEM Mighty Mule board runs $270 to $410 installed. These prices are written and handed to you before any work starts, under Haven Standard Clause 1. We don’t quote by phone, guess from photos, or bill above the written number. Call (754) 714-5786 for a free estimate, and we’ll put the exact price in front of you before a technician touches the gate.
Serving Hollywood, FL - Our Local Coverage Area
We’re based in the Hollywood area and know this community well through Gate Repair - Hollywood. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Mighty Mule Gate Repair in Hollywood
No. Vance Gate Repair is an independent Mighty Mule service provider, not a manufacturer-authorized dealer or affiliate. That matters less than you might think: we use OEM Mighty Mule parts, we know the model lines and their failure modes better than most authorized installers in Broward County, and we don’t push a gate replacement just because the opener is older. If your Mighty Mule can be repaired safely and within code, that’s what we quote.
OEM whenever it’s available. We stock Mighty Mule control boards, receivers, and actuators in the van specifically because Hollywood’s salt-air environment eats aftermarket components faster than the warranty can cover them. If an OEM part is back-ordered, we’ll show you the expected timeline and give you the choice to wait or use an equivalent. You decide, with the price in writing first.
Most repairs are completed in one visit, usually 60 to 90 minutes on site. The exception is when a gate needs HVHZ code compliance work, which can add a day or two for permit coordination. We’ll tell you the timeline before we start, and the written price doesn’t change just because the job took longer than expected.
All of them that matter in Hollywood: FM200 through FM500, MM260 through MM572, and the MMKits series. The MM371 and MM571 are the most common on Hollywood’s 1950s-1970s ranch homes, while the MMKits show up heavily in the western HOA communities near I-75. If you’re not sure which model you have, read the number off the control board or the arm housing, and we’ll tell you what it is and what it’s worth repairing.
Between $185 and $460 for most repairs, with the specific price written and handed to you before any work begins. The factors that shift the cost in Hollywood specifically: whether salt corrosion has spread to the hinge hardware (which adds stainless fastener replacement), whether the gate passed an HVHZ wind-load review, and whether the existing Mighty Mule opener is the correct model for the gate’s weight. Call (754) 714-5786 for an exact quote, free.
Service Areas Near Hollywood
We run Mighty Mule service calls throughout Hollywood, including Hollywood Hills, Liberia, and the beachside blocks, plus the surrounding cities. If you’re just north of the county line or a few minutes across the Intracoastal, we cover Dania Beach and Pembroke Park, and our regular route includes Mighty Mule service in Dania Beach and Mighty Mule service in Pembroke Park. We also reach Hallandale Beach, Ojus, and Aventura when the route allows same-day dispatch. For the full coverage map, see our Hollywood service area page.
Book Your Mighty Mule Service in Hollywood Today
Call (754) 714-5786 and you’ll talk to a live person, any hour. Tell us what the gate is doing wrong, and we’ll name the likely fix and the price range before we arrive. Same-day dispatch is available for most Hollywood repairs, especially where a gate is stuck open or won’t close. We bring the parts, the written quote, and the documentation habit that’s been running this company since 2014.
Written by Adrian Vance, owner at Vance Gate Repair, serving Hollywood since 2014.